|
672.
|
|
|
Delay time between two horizontal segments. Introducing such a delay can cause better adhesion to previous layers at the connection points, while too long delays cause sagging. Only applies to Wire Printing.
|
Context: |
|
wireframe_flat_delay description
|
|
|
|
Die Verzögerungszeit zwischen zwei horizontalen Segmenten. Durch eine solche Verzögerung kann eine bessere Haftung an den Verbindungspunkten zu vorherigen Schichten erreicht werden; bei einer zu langen Verzögerungszeit kann es allerdings zum Herabsinken von Bestandteilen kommen. Dies gilt nur für das Drucken mit Drahtstruktur.
|
|
Translated by
Thomas Karl Pietrowski
|
|
|
|
Located in
fdmprinter.def.json
|
|
673.
|
|
|
WP Ease Upward
|
Context: |
|
wireframe_up_half_speed label
|
|
|
|
Langsame Aufwärtsbewegung bei Drucken mit Drahtstruktur
|
|
Translated by
Thomas Karl Pietrowski
|
|
|
|
Located in
fdmprinter.def.json
|
|
674.
|
|
|
Distance of an upward move which is extruded with half speed. ![](/@@/translation-newline)
This can cause better adhesion to previous layers, while not heating the material in those layers too much. Only applies to Wire Printing.
|
Context: |
|
wireframe_up_half_speed description
|
|
|
represents a line break.
Start a new line in the equivalent position in the translation.
|
|
|
|
Die Strecke einer Aufwärtsbewegung, die mit halber Geschwindigkeit extrudiert wird. ![](/@@/translation-newline)
Dies kann zu einer besseren Haftung an vorhergehenden Schichten führen, während gleichzeitig ein Überhitzen des Materials in diesen Schichten vermieden wird. Dies gilt nur für das Drucken mit Drahtstruktur.
|
|
Translated by
Thomas Karl Pietrowski
|
|
|
|
Located in
fdmprinter.def.json
|
|
675.
|
|
|
WP Knot Size
|
Context: |
|
wireframe_top_jump label
|
|
|
|
Knotengröße für Drucken mit Drahtstruktur
|
|
Translated by
Thomas Karl Pietrowski
|
|
|
|
Located in
fdmprinter.def.json
|
|
676.
|
|
|
Creates a small knot at the top of an upward line, so that the consecutive horizontal layer has a better chance to connect to it. Only applies to Wire Printing.
|
Context: |
|
wireframe_top_jump description
|
|
|
|
Es wird ein kleiner Knoten oben auf einer Aufwärtslinie hergestellt, damit die nächste horizontale Schicht eine bessere Verbindung mit dieser herstellen kann. Dies gilt nur für das Drucken mit Drahtstruktur.
|
|
Translated by
Thomas Karl Pietrowski
|
|
|
|
Located in
fdmprinter.def.json
|
|
677.
|
|
|
WP Fall Down
|
Context: |
|
wireframe_fall_down label
|
|
|
|
Herunterfallen bei Drucken mit Drahtstruktur
|
|
Translated by
Thomas Karl Pietrowski
|
|
|
|
Located in
fdmprinter.def.json
|
|
678.
|
|
|
Distance with which the material falls down after an upward extrusion. This distance is compensated for. Only applies to Wire Printing.
|
Context: |
|
wireframe_fall_down description
|
|
|
|
Die Strecke, die das Material nach einer Aufwärts-Extrusion herunterfällt. Diese Strecke wird kompensiert. Dies gilt nur für das Drucken mit Drahtstruktur.
|
|
Translated by
Thomas Karl Pietrowski
|
|
|
|
Located in
fdmprinter.def.json
|
|
679.
|
|
|
WP Drag Along
|
Context: |
|
wireframe_drag_along label
|
|
|
|
Nachziehen bei Drucken mit Drahtstruktur
|
|
Translated by
Thomas Karl Pietrowski
|
|
|
|
Located in
fdmprinter.def.json
|
|
680.
|
|
|
Distance with which the material of an upward extrusion is dragged along with the diagonally downward extrusion. This distance is compensated for. Only applies to Wire Printing.
|
Context: |
|
wireframe_drag_along description
|
|
|
|
Die Strecke, die das Material bei einer Aufwärts-Extrusion mit der diagonalen Abwärts-Extrusion nach unten gezogen wird. Diese Strecke wird kompensiert. Dies gilt nur für das Drucken mit Drahtstruktur.
|
|
Translated by
Thomas Karl Pietrowski
|
|
|
|
Located in
fdmprinter.def.json
|
|
681.
|
|
|
WP Strategy
|
Context: |
|
wireframe_strategy label
|
|
|
|
Strategie für Drucken mit Drahtstruktur
|
|
Translated by
Thomas Karl Pietrowski
|
|
|
|
Located in
fdmprinter.def.json
|